PicoLog DrDAQ USB Data Logger

De DrDAQ is een low cost data logger van Pico Technology. Hij wordt compleet voor gebruik geleverd inclusief kabels, software en voorbeelden vind u hier.

•Erg goedkoop
•Ingebouwde sensoren voor licht, geluid (level en waveforms) en temperatuur
•Meet pH - u kunt iedere standaard pH elektrode gebruiken
•Poorten voor externe sensoren
•Gebruik DrDAQ om snelle signalen op te vangen (Bijv. sound waveforms)
•Outputs voor control experimenten
•Simpel plug in uw PC en meet - geleverd met zowel (oscilloscope) en PicoLog (data logging) software

DrDAQ heeft ingebouwde sensoren voor licht, geluid (zowel sound level en sound waveforms) en temperatuur. Hij kan ook zowel voltage als weerstand meten. Als toevoeging heeft hij ook een aansluiting voor standaard pH elektrodes en connectors voor optionele externe sensoren (temperatuur, vochtigheid, druk en meer). Om meer uit te vinden over DrDAQs sensoren, en om meer voorbeelden van waveforms, simpel klik met uw linkermuisknop op het punt van interesse op bovenstaande foto.
DrDAQ Data Logger General Specifications
Number of channels 14
Maximum sampling rate
Block mode
USB streaming

1 MS/s#
100 kHz#
Memory depth (block mode) 16 kS#
Memory depth (USB streaming)
PicoLog
PicoScope
Using the API

1 MS#
20 MS#
unlimited

# Shared between active channels.

Oscilloscope/Spectrum Analyser Channel
Bandwidth 100 kHz
Resolution 8 bits
Input characteristics 1 MΩ
Input type Single-ended, BNC connector
Input coupling DC
Input ranges (full scale) ±1.25 V, ±2.5 V, ±5 V, ±10 V
DC accuracy ±3%
Timebases 10 µs/div to 5000 s/div
Function Generator/Arbitrary Waveform Generator (AWG)
Channels 1
Connector BNC
Standard waveforms Sine, square, triangle, ramp (up/down), DC level
Function generator frequency range DC to 20 kHz
Signal amplitude ±1.5 V
Signal offset ±1.5 V
AWG buffer size 4096 samples
AWG update rate 2 MS/s (maximum)
AWG resolution 10 bits
Built–in sensors/Outputs
Channel Range Resolution Accuracy
Sound waveform ±100 ±0.2 not calibrated
Sound level 55 to 100 dBA 1 dBA 5 dBA
Temperature -10 to +70 °C 0.1 °C @ 25 °C 2 °C @ 25 °C
Light 0 to 100 0.1 not calibrated
RGB LED 16.7 million colours 8 bit x 3 not applicable
Analogue Inputs
Type Connector Range Resolution Accuracy
pH BNC 0 to 14 pH 0.02 pH sensor calibration dependent
Redox/ORP BNC (shared with pH) ±2000 mV @ 1012 Ω 1.2 mV sensor calibration dependent
Resistance Screw terminal 0 to 1 MΩ 250 Ω @ 10 k 5%
External sensors 3 x FCC68 4/4 Measure 0 to 2.5 V
(Also supply power to external sensors and identify sensor type via ID resistor.)
1 mV 1%
Configurable Digital IO
Channels 4
Connector type Screw terminals
Input characteristics 0 to 5 V (Low:0- 0.8 V, High: 2 -5.5 V)
TTL compatible
Output characteristics 3.3 V, 2.2 kΩ output impedance
PWM output
Period
Pulse
Resolution

<65535 µs
<65535 µs
1 µs
Available on 2 Digital IO channels
Pulse counting Up to 65535 counts @ 500 kHz
Available on 2 Digital IO channels
Physical Properties
Dimensions 77 x 70 x 23 mm  (approx 3 x 2.7 x 0.9 in)
(includes BNC connectors)
Weight 60 g  (approx 2.1 oz)
Software
PicoLog for Windows PicoLog data acquisition software can collect up to 1 million samples. Features include:
Multiple views — view data as a graph, spreadsheet or text
Parameter scaling — convert raw data into standard engineering units
Math functions — use mathematical equations to calculate additional parameters
Alarm limits — program an alert if a parameter goes out of a specified range
IP networking — transfer measurements via a LAN or over the Internet
Full details on PicoLog
PicoScope 6 for Windows PicoScope 6 is your complete test and measurement lab in one application. Features include:
Capture modes: oscilloscope, spectrum and persistence.
Channel maths: calculate the sum, difference, product, inverse or create your own custom function using standard arithmetic, exponential and trigonometric functions.
Mask limiting testing: pass/fail, failure count, total count.
serial Decoding: decode data from a serial bus such as I²C.
Automated measurements
Scope mode: AC RMS, true RMS, cycle time, DC average, duty cycle, falling rate, fall time, frequency, high pulse width, low pulse width, maximum, minimum, peak–to–peak, rise time and rising rate.
Spectrum mode: frequency at peak, amplitude at peak, average amplitude at peak, total power, total harmonic distortion (THD % and THD dB), total harmonic distortion plus noise (THD+N), spurious-free dynamic range (SFDR), signal+noise+distortion to signal+noise ratio (SINAD), signal to noise ratio (SNR) and intermodulation distortion (IMD).
Export data formats: comma separated values (CSV), tab delimited (TXT), Windows bitmap (BMP), graphics interchange format (GIF), portable network graphics (PNG), MATLAB 4 format (MAT).
Full details for PicoScope 6
Software development kit Includes drivers and example code for various programming languages including C, C++, Excel and LabVIEW. Download SDK
Language Support
Software
PicoLog

PicoScope 6

Full support for: English, Français, Deutsch
Menus and dialogs only for: Italiano, Español, Svenska
Full support for: English, Deutsch, Español, Français, Italiano
Menus and dialogs only for: 中文 (简体), 中文 (繁體), Čeština, Dansk, suomi, Ελληνικά, Magyar, 한국어, 日本語, Norsk, Polski, Português, română, Русский, Svenska, Türkçe
Documentation
User’s guide
Programmer’s guide

English
English
General
Data sheet English 中文 (简体), Deutsch, Español, Français, Italiano
Additional hardware (supplied) USB 2.0 cable, user manuals, software CD–ROM
PC interface USB 2.0 (USB 1.1 compatible)
Power requirements Powered from USB port
Compliance European EMC and LVD standards
FCC Rules Part 15 Class A
RoHS compliant
Total Satisfaction Guarantee In the event that this product does not fully meet your requirements you can return it for an exchange or refund. To claim, the product must be returned in good condition within 14 days.
Warranty 5 years